Oven Repair
Ovens that will not heat, heat unevenly, fail self-clean or throw a code, gas and electric, range and wall ovens.
DetailsInduction cooktop repair in Jacksonville
Induction cooktops have no flame and no glowing element, just coils, power boards and a cooling fan under the glass. When one fails, the cooktop usually tells you with a code, and the code is where we start.
- Error code diagnosis
- Power boards and fans
- Bosch, GE, Samsung, Frigidaire
Updated October 2026
Quick answer
Induction cooktop repair in Jacksonville usually involves a failed power or inverter board, a stopped cooling fan, a damaged coil or a control and touch panel fault. We read the error code, test the board and fan for the failing zone, and quote the repair before ordering parts.
How induction cooktops fail
Each induction zone has a copper coil under the glass and a power board that drives it at high frequency. The electronics make heat, so a fan pulls air across the boards through vents under the cooktop. When that fan stops or the vents are blocked, the boards overheat and the cooktop shuts zones down or throws an overheat code.
Most induction repairs are board-level: a power module for one pair of zones, a touch control, or the fan. Replacement parts are model-specific and are usually ordered, so the first visit diagnoses and confirms the part, and the second installs it.
Cost
What induction cooktop repair costs
Induction repairs are quoted after diagnosis because the price depends almost entirely on which board or part has failed and what it costs for your model.
- Board or fan. A fan is a modest repair; a power board is a larger one.
- Model availability. Parts are model-specific and usually ordered.
- Glass damage. A cracked top changes the repair entirely.
- Supply wiring. A loose terminal connection is a quick fix.
No flat price over the phone. We price after the diagnosis, part and labor separately, so you can decide before any work starts.
Compare the options
Induction compared with radiant electric
| Point | Induction | Radiant electric |
|---|---|---|
| Heats with | Magnetic field into the pan | Glowing element under glass |
| Common failure | Power board or fan | Element or switch |
| Cookware | Magnetic only | Any flat pan |
| Typical repair | Board-level, often ordered | Element swap, often same visit |
The jobs this page covers
01
Induction Error Codes
Induction cooktops log codes for overheating, a failed coil, a communication fault between boards or a voltage problem at the supply. We read the code, then check the supply voltage at the terminal block, because a loose connection there causes many strange faults that look like board failures. Then we test the board that drives the failing zone. Codes vary by brand and model, so we use the service data for your model rather than general guesses, and we explain the code in plain words.
02
Cooling Fan and Board Repair
A cooktop that works for a few minutes and then shuts off, or that works only on low settings, is often protecting itself from heat. We check that the cooling fan spins and that the vent space under the cooktop is not blocked by a drawer or stored items. A failed fan is a modest repair. A power board that has burned out after running hot is a bigger one, and we replace the fan at the same time so it does not happen again.
03
Pan Not Detected
Induction only works with magnetic cookware. If a magnet does not stick to the bottom of the pan, it will not heat. If magnetic pans are not detected on one zone but work on others, the coil or its board connection for that zone is suspect. We test the coil resistance and the board output for that zone, and confirm whether the fault is on the coil, the harness or the board before ordering anything. That keeps you from paying for a board the cooktop did not need.
Induction in newer First Coast kitchens
Induction cooktops are showing up more often in newer and remodeled kitchens around Jacksonville, usually installed over a drawer stack. That drawer is also where the cooktop pulls its cooling air from, and a drawer packed tight against the underside starves the fan. We check the clearance at every induction call and show you where the air needs to flow so the boards stay cool.
Step by step
How we diagnose induction
- 1
Read the code
Service data for your exact model.
- 2
Check supply and fan
Voltage at the terminal block and fan operation.
- 3
Test the zone
Coil and board output for the failing zone.
- 4
Order and install
Confirmed part ordered, installed, all zones tested.
WhirlpoolGESamsungLGFrigidaireMaytagKitchenAidBoschElectroluxKenmoreSub-ZeroWolfThermadorSpeed Queen
Induction cooktops we see: Bosch, GE, Samsung, Frigidaire, Thermador, KitchenAid and Electrolux.
FAQ
Induction Cooktop Repair questions
The pan may not be magnetic. Test it with a magnet. If magnetic pans fail on only one zone, that zone's coil or board is suspect.
Overheat protection is common when the cooling fan fails or the air path under the cooktop is blocked.
It depends on the part. Fans and wiring repairs are modest; power boards cost more. We quote after diagnosis.
No. Stop using it and turn it off at the breaker until the glass top is replaced.
Yes, induction ranges use the same zones and boards as cooktops.
Also on the list
Related repairs
Stove and Cooktop Repair
Gas burners that click without lighting, electric coils and glass radiant elements that will not heat.
DetailsMicrowave Repair
Over-the-range, built-in and drawer microwaves that will not heat, spark or have a dead keypad.
DetailsRange Hood Repair
Range hood fans, lights and controls repaired, plus grease cleanup and weak-draw diagnosis.
DetailsInduction cooktop throwing a code?
Write down the code and the model number, then call. That lets us check parts before the first visit.